#168716  by TI4-1009
 Fri Nov 27, 2020 8:40 pm
Last month my old bandmate from the 60s gave me his Silverface '76 Twin Reverb that had been sitting broken in his basement for a few decades. Although I've built an amp from a kit (BYOC Tweed Royal) I've been pretty intimidated by the discussions about Jerryfing or Alembicizing the Twin. The schematic has always looked like Mandarin chicken scratch and the discussions about "replacing the .047 coupling cap with mil-spec..." left me with eyes glazed over and wandering in the wilderness.

But with a lot of help from the gurus over on the TDPRI board I got the thing up and running! Three phases: 1- make it run; 2- upgrades needed for a 45-year old amp; 3- minor sonic improvements. I have an SMS/JG, so I really don't need a Jerrified twin at this point. I may eventually Blackface it (but it sounds pretty freekin good as is). And gloryoski- I can find my way around the schematic now and almost understand what everything is and does! Bucket List!

And- bonus- I have the option of running it through my Jerry rig cab loaded with JBL Ks!

Here's what I ended up doing:

Replaced screen and grid resistors and replaced two power tubes
Replaced all electrolytic caps
Replaced rectifier diodes
Added bias pot
Removed thermistor
Regrounded power cord plug
Bypassed convenience receptacle
Converted ground switch to NFB switch
Added pop resistor to standby switch
Replaced grid stopper and input resisitors
Replaced normal channel jacks
Replaced 8 slope and plate resistors
Replaced treble caps with mica
Replaced V3 and V4
Replaced V4 socket
Replaced V3 cathode resistor with a 2k2 and added a 22/25 cap
Replaced the phase inverter .001 and V4 .003 coupling caps with orange drops
Cleaned all pots and jacks
Rewired the footswitch
Vacuumed the cabinet, cleaned tolex with Dawn, 409, and Armor All
Removed and cleaned knobs and faceplate
Replaced chassis straps (one was completely rusted over)
Polished tilt-back legs

Here's a link to the help thread (many photos embedded):

https://www.tdpri.com/threads/diving-in ... p.1052053/

If you're headed down this path and on a steep learning curve like I was, two great resources are:

Uncle Doug's youtube videos (he's a great teacher):

https://www.youtube.com/user/Stratosaurus1/videos

And Rob Robinette's web page:

https://robrobinette.com/Amp_Stuff.htm
Last edited by TI4-1009 on Fri Nov 27, 2020 8:55 pm, edited 3 times in total.
NeilG1 liked this
 #168717  by TI4-1009
 Fri Nov 27, 2020 8:41 pm
Here's a few photos:

Image

Image

Image

Image
 #168718  by Jon S.
 Fri Nov 27, 2020 9:17 pm
Here's something I don't get. Today, such a premium is placed on super neat PTP wiring with a minimum of wire length. People pay small fortunes for such amps. Yet so many of the great BF Fenders of yesteryear have wiring that looks like rats' nests/spaghetti bowls. And they sound great!
 #168719  by Searing75
 Fri Nov 27, 2020 10:47 pm
Great job man! So much fun refurbishing these old Fenders. Just a joy to work on.
 #168724  by TI4-1009
 Sat Nov 28, 2020 3:04 pm
Jon S. wrote:
Fri Nov 27, 2020 9:17 pm
Here's something I don't get. Today, such a premium is placed on super neat PTP wiring with a minimum of wire length. People pay small fortunes for such amps. Yet so many of the great BF Fenders of yesteryear have wiring that looks like rats' nests/spaghetti bowls. And they sound great!
That's where they stuff all the "mojo". :lol: :lol: :lol:
Jon S. liked this